← Back to Learning Hub

How to Choose a Commercial Dishwasher for Your Restaurant

Commercial dishwasher with its rack pulled out in a restaurant kitchen
Learning Hub · Equipment Buying Guide

How to Choose a Commercial Dishwasher for Your Restaurant

November 2026 · By Faith, Kitchen Arena · About 5 minutes to read

It's 1.30pm, the lunch crowd is still coming in, and the front is asking for plates. Your dishwasher is on its third cycle in ten minutes and the dirty racks keep piling up. Most owners only find out their machine is too small on a day like this. Whether you're setting up your first kitchen or replacing a tired old machine, choosing a commercial dishwasher for your restaurant is less about the brand and more about your numbers: how many racks you wash, what power your shop has, and where the steam and water will go.

The three main types

Most restaurants in the Klang Valley use one of these three.

UndercounterHood type (pass-through)Conveyor
Racks per hour*About 20–40About 40–80150 and above
SpaceAbout 600 mm wide, fits under a counterAbout 650 mm wide, plus tables on both sidesSeveral metres long
PowerSingle-phase or three-phaseUsually three-phase, around 10–12 kWThree-phase, much higher load
Opening heightAbout 320 mmAbout 440 mmDepends on model
Usually suitsCafés, bars, small kiosksMost sit-down restaurantsHotels, canteens, central kitchens

*Brochure figures. Real output is lower. More on that below.

Start with your rush hour, not your daily total

Clean plates, cups and glasses stacked in a restaurant after washing

A dishwasher doesn't fail on a quiet Tuesday. It fails at peak. So work out how many racks you wash in your busiest hour.

Say you run an 80-seat restaurant in Petaling Jaya and serve 200 customers over a two-hour lunch. Each customer uses a plate, a bowl and a glass. Add trays, sauce dishes and kitchen utensils, and that's easily 25 to 30 racks an hour.

A small café doing 10 racks an hour and a hotel canteen doing 200 need very different machines. Your rush-hour number tells you which type to look at.

Why the brochure number is too optimistic

Staff loading plates into a dishwasher rack

The racks-per-hour figure on a spec sheet is calculated on the shortest wash cycle, back to back, with no time for loading. One popular hood-type model, for example, is rated at 40 racks an hour on its 90-second cycle, but only 24 on its 150-second cycle and 17 on its longest one.

Two more things slow it down:

Loading time. Someone has to scrape, load, wait, and unload. From what we see in kitchens, real output is often closer to two-thirds of the brochure figure.

Cold water. Many machines assume a warm water supply. Connect them to cold water and the manufacturer itself says the cycle will run longer, because the machine has to wait for the water to heat up.

A simple rule: take your peak racks per hour and choose a machine whose normal cycle, not its fastest one, can handle it with some room to spare.

What buyers often overlook

Your power supply. A typical hood-type machine needs three-phase 400V power and draws around 10 to 12 kW. Many shop lots only have single-phase. Upgrading with TNB takes time and money, so check your DB box before you choose. Some models come in single-phase versions, but they usually have a smaller heater.

Electricity, not water, is the real running cost. To sanitise, the final rinse is heated to about 82°C or more. The water itself is cheap. Heating it is not. For a busy restaurant, the electricity to heat the rinse water can cost several times more than the water bill for the machine. A model with heat recovery or a well-insulated hood can bring this down, so ask about it.

The opening height. A hood-type machine usually takes items up to about 440 mm tall, an undercounter about 320 mm. If you need to wash big trays, GN pans, woks or tall jugs, measure them first.

Steam. Every time the hood opens, a cloud of steam comes out. In a shop lot with a low ceiling, it condenses, drips and leads to mould and peeling paint. Plan for a condensate hood above the machine, or choose a model with a built-in steam condenser.

Water hardness. Many manufacturers specify soft water, and some will not cover scale damage under warranty if there's no softener. Test your water and ask whether the model has a built-in softener or needs a separate one.

Where the drain goes. Hot, soapy dishwasher water can carry grease straight through a grease trap and into the drain, where it cools and blocks the pipe further down. Ask your plumber or contractor how the dishwasher should be connected at your premises.

Space around the machine. A pass-through machine needs a dirty table with a pre-rinse spray on one side and a clean table on the other, plus somewhere to keep spare racks. Scraping food off first also keeps the wash water cleaner for longer.

Chemicals. Commercial machines use dosing pumps for detergent and rinse aid. Household dishwashing liquid will foam and can damage the machine. Include chemicals in your monthly cost.

Cook stir-frying with a wok during a busy lunch service in a restaurant kitchen

Which commercial dishwasher is right for your restaurant?

If you wash fewer than about 20 racks in your busiest hour, an undercounter machine is usually enough. Between about 20 and 60, a hood-type machine is the usual choice for restaurants. Beyond that, or if you serve hundreds of meals in one sitting, it's time to look at a conveyor.

Whichever you choose, check three things before you pay: your power, your drain and your space. Then ask who will service the machine, and how quickly they can come when it stops in the middle of lunch.

You can compare undercounter, hood-type and conveyor models in our dishwasher range.

Not sure which size you need?

Tell us your seats, your busiest hour and your power supply. Our team will recommend a machine and check the installation needs with you.

Browse dishwashers Get a quote

Sources: Electrolux Professional · MEIKO spec sheet · FOODSAFE · NI Business Info

This article is general guidance based on our experience. Specifications, power requirements and warranty terms vary by model, so confirm details with your supplier and a qualified technician before you buy.